This is either because you are running off of a front USB port on your PC or you are using a bad cable or you did not install your drivers correctly. If you have a 1 or a 2 there you're computer sees your phone. Notice at the bottom of the window it says _IsConenctedPhone. If you did it right, the second screen will come up. I've never had it go straight into Download Mode from this screen, but some how it threw an SU command at the phone and did it.Īny ways, here are screen shots of exactly how your setup should be when you run the KP500 software, keeping in mind that I am flashing 3.02 in this example. I was actually in the OS and ran the tool with debugging enabled. Ok, so I just tried the flash program again to try and find your error message, and apparently having root on the phone changes the game a little, but in a good way. You may wish to do a factory reset just to be safe.Įnjoy the fact that you can now recover your phone if you do something wrong (in most cases) I did not do a factory reset and everything came back as it was, but with a new firmware version. Wait for your phone to finish flashing and let it reboot on its own. Every so often a message will go by about "model dll message not found". If you did it right, you will get a percentage indicator that goes past 15%. bin file.Īt this point if you did something wrong with driver setup or not disabling the modem driver, you will get a page error. It will find your phone and go thru extracting the cab file and then extracting a. It will most likely tell you that your phone is disconnected. Input the full file name of your cab (aka version) without the Cab (i.e. Input the full path to your cab file including. cab file to the same directoryĬhoose I "Flash with assistance (file. I highly recommend using the official cable that came with the phone when doing a flash and not being on and USB hubs.Įxtract KP500 tool into a directory (i.e. Plug in usb cable while holding both buttons.) Reboot your phone in "Download Mode" (re-insert your battery and replace the back plate.
Remove your battery and remove your memory card. Go into your Windows Device Manager and disable the device under Modems -> LGE AndroidNet for VZW USB Modem If you have adb on your PC, you can test your connection buy running ADB shell and seeing if your phone connects correctly Then set phone to Debug mode and make sure all additional drivers install correctly. Run the driver package and let it run its course. It will fail to flash otherwise.Ĭharge your battery to full, not just 80% or so. If your fire wall asks if you want to give the LG tool access to the internet, then let it. Putting your phone into charge only mode will activate a special area of the phone and Windows will show up a new drive containing the USB drivers)Īn Internet connection on the computer you are flashing with. (I went to grab the link from the site, but the Verizon drivers are no longer listed there. Unified Verizon Drivers from LG Site or from your phone. LG Update tool from LG site ( LG Mobile Support: Find the Latest Drivers & Product Guides | LG USA) KP500 ( ) - Personally hosted, so please don't hammer the site If you do something wrong, you will brick your phone, especially if it's during the final steps as flashing the cab actually deletes your recovery partition before flashing the new one. I take no responsibility if your mess up your phone in the process. Here is instructions on how to flash a new firmware. I've decided that this should be in it's own thread as it is relevant to most of the work going on right now and should not be buried inside of another thread. IF YOU KEEP BOOT LOOPING INTO CWM, THEN FLASH THE BOOT LOOP FIX FOUND HERE. Alternatively, some programs, notably PC games, require that the DLL file is placed in the game/application installation folder.įor detailed installation instructions, see our FAQ.DO NOT FLASH THIS IF YOU ARE STUCK IN CWM. In the vast majority of cases, the solution is to properly reinstall flash.dll on your PC, to the Windows system folder.
Try installing the program again using the original installation media or contact your system administrator or the software vender for support. flash.dll is either not designed to run on Windows or it contains an error.Reinstalling the program may fix this problem. The code execution cannot proceed because flash.dll was not found.There was a problem starting flash.dll.
Try reinstalling the program to fix this problem. The program can't start because flash.dll is missing from your computer.The most commonly occurring error messages are: For instance, a faulty application, flash.dll has been deleted or misplaced, corrupted by malicious software present on your PC or a damaged Windows registry. Errors related to flash.dll can arise for a few different different reasons.